ECP202 Condensate Pump for Condensing Boilers – 1.9 l Tank
The ECP202 condensate pump is used for the automatic removal of condensate water generated during the operation of condensing boilers. It is a solution for installations where gravitational condensate drainage is impossible or difficult, for example, due to the location of the drainage point.
The device is equipped with a 1.9 l tank and an automatic start and stop system. Built-in sensors monitor the level of accumulated condensate and allow for overflow detection. This ensures that the condensate removal process occurs without the need for manual tank emptying during proper device operation.
The ECP202 model offers a flow rate of 250 l/h at a lifting height of 0.3 m, 190 l/h at 1.5 m, and 115 l/h at 2.7 m. The maximum lifting height is 4.6 m. The fan-cooled motor is equipped with thermal protection, and the device housing has an IP20 protection rating.
Main Advantages
- Automatic Operation – the pump automatically starts and stops depending on the condensate level.
- 1.9 l Tank Capacity – allows for the accumulation of condensate before pumping out.
- 250 l/h Flow Rate at 0.3 m – provides performance suitable for installations meeting the device's hydraulic requirements.
- Maximum Lifting Height of 4.6 m – enables the transport of condensate to a drain located above the pump tank.
- Built-in Water Level Sensors – responsible for monitoring the condensate level and detecting overflow.
- Motor Thermal Protection – protects the drive from the effects of excessive temperature rise.
- Adaptation to Condensate with pH from 2.5 – allows use in installations with condensate meeting the device's chemical requirements.
- 230 V AC Mains Power Supply – allows the device to be powered from a properly prepared electrical installation.
Technical Specification
Parameter | Value |
|---|
Model | ECP202 |
Device Type | Tank Condensate Pump |
Application | Gas and Oil Boilers, Condensing Devices |
Maximum Lifting Height | 4.6 m |
Flow Rate at 0.3 m | 250 l/h |
Flow Rate at 1.5 m | 190 l/h |
Flow Rate at 2.7 m | 115 l/h |
Tank Capacity | 1.9 l |
Supply Voltage | 220–240 V AC |
Nominal Voltage | 230 V AC |
Supply Frequency | 50 Hz |
Input Power P1 | 60 W |
Current Consumption | 0.6 A |
Noise Level from 1 m | < 50 dB(A) |
Control System | Automatic Start and Stop |
Sensors | Built-in Water Level Sensors |
Overflow Detection | Yes |
Motor Cooling | By Fan |
Motor Thermal Protection | 120°C |
Motor Insulation Class | F |
Protection Rating | IP20 |
Minimum Allowable Condensate pH | 2.5 |
Maximum Condensate Density | 1000 kg/m³ |
Power Cable Length | 145 cm |
Device Weight | 1.5 kg |
ECP202 Pump Performance
The performance of the condensate pump depends on the height to which the liquid must be pumped.
Lifting Height | Flow Rate |
|---|
0.3 m | 250 l/h |
1.5 m | 190 l/h |
2.7 m | 115 l/h |
The maximum lifting height is 4.6 m.
When selecting a pump, consider the vertical discharge section, pipe lengths, connection diameters, and hydraulic resistance of the installation. Do not assume that a flow rate of 250 l/h is available at the maximum lifting height.
Application of ECP202 Condensate Pump
The ECP202 is primarily intended for the automatic removal of condensate from heating devices.
Main Applications:
- Condensing Gas Boilers – removal of condensate to a properly prepared drain.
- Condensing Oil Boilers – transport of condensate generated during system operation.
- Heating Devices Using Condensation – removal of condensate in accordance with the pump's allowable parameters.
- Installations Without Gravity Drainage – pumping condensate to a collection point located above the pump tank.
Before use, check the temperature, pH level, and amount of generated condensate, as well as installation conditions.
Why Choose the ECP202 Condensate Pump?
The ECP202 combines a 1.9 l tank, automatic control, and specified flow characteristics at various lifting heights. This facilitates the selection of the pump for heating installations where condensate requires mechanical removal.
Built-in water level sensors, overflow detection function, and motor thermal protection are practical solutions supporting the safe operation of the device.
The pump is intended for both installers and service technicians of heating systems, as well as users seeking a solution for removing condensate from a boiler.